In fact, any kind of antioxidant can not fully meet these conditions. Therefore, in actual application, it is often based on the variety, use and processing method of engineering plastics, using the strengths of various additives and cooperating to produce synergistic effects.

Antioxidant is a kind of chemical substance. When it is only a small amount in the polymer system, it can delay or inhibit the progress of the polymer oxidation process, thereby preventing the aging of the polymer and prolonging its service life. It is also called " Anti-aging agent".

Common tetra-group lead, ferrocene, MMT (methylcyclopentadiene trikarbonyl manganese) or CMT is common, because metal deposits can occur in the inside of the launching machine, resulting in a cylinder wear, spark plug ignition Poor problems such as poisoning, oxygen sensors and ternary catalysts, have been prohibited or constrained. The addition of tetra-element and ferrocene added is known as national standards, and the manganese-based anti-explosive agent is strictly constrained (the detection limit is less than 0.018 g / L).

Chemical nature: Forbidden qualitative: strong oxidizing agent, strong reducing agent, strong acid, strong base. Ecological nature: Ecotoxicity EC50: 1.2 ~ 1.51mg / L (luminous bacteria, microtox toxicity test) Biodegradability Miti-I test, initial concentration of 100 mg / L, sludge concentration 30 mg / L, 2 weeks later degraded 77%. Non-biodegradability In the air, when the hydroxyl radical concentration is 5.00 × 105 / cm3, the degradation of the half-life is 7.8d (theory). Other harmful effects The material is damaged by the environment and should pay spe

The octane is the most important quality indicator of the vehicle gasoline.

A substance that can reduce the surface tension of water, solution, suspension, etc., prevent the formation of foam, or reduce or eliminate the original foam. [1]

Phosphorus pentachloride is mainly used as a chlorination reagent for alcohols, carboxylic acids, amides, aldehydes, ketones, enols, and Beckmann rearrangement reagents. It is used as a chlorination agent and catalyst in organic synthesis, and is used in the production of medicines, dyes, and chemical fibers. It is also the raw material for the production of phosphazene chloride and phosphorus oxychloride.

From the perspective of physics, the methods to eliminate foam mainly include placing baffles or filters, mechanical stirring, static electricity, freezing, heating, steam, radiation, high-speed centrifugation, pressure and decompression, high-frequency vibration, instantaneous discharge and ultrasonic (acoustic) Liquid control), etc., these methods promote the gas permeation rate at both ends of the liquid film and the drainage of the bubble film to varying degrees, so that the stability factor of the foam is smaller than the attenuation factor, and the number of foams is gradually reduced.

1.4, 4 '- methylene bis (2-chlorocene) The molecular weight is 267.15, the molecular formula is C13H12N2 CL2

Light yellow to white granular crystals (semi-circular) white to light yellow loose crystals, heating is made black.

Aspirational antioxidants should have the following conditions: ①Should have high anti-oxidation ability; ②Good compatibility with resin, no precipitation; ③Good processing function, non-volatile and non-decomposing at the processing temperature of high polymer; ④Good resistance to extraction, insoluble in water and oil; ⑤The color of itself is best to be colorless or light-colored, so as not to pollute the product; ⑥Non-toxic or low-toxic; ⑦Low price. In fact, any kind of antioxidant can not fully meet these conditions.

HCFC-141b (monofluorodichloroethane) is a high-purity liquid widely used in cleaning and solvent fields. Because its damage to the ozone layer is 1/10 of CFC-113, it is designated as an ideal substitute for fully halogenated chlorofluorocarbons. HCFC-141b is a widely used non-perhalogenated chlorofluorocarbon. Although its destructive effect on the ozone layer has been greatly reduced compared to fully halogenated chlorofluorocarbons, it can still cause damage to the ozone layer that is difficult to recover. As a result, its use is gradually being reduced around the world.

Features: Contains two hydroxyl groups and one amino group. Hydroxyl reduces the vapor pressure, increases the solubility, is conducive to the absorption of acid gas, and can increase the concentration, reduce circulation, and reduce energy consumption. The presence of the methyl group in the amino group reduces the alkalinity and activity of the amino group and reduces the CO2 absorption rate. The molecular weight is 119.16, the melting point is -21°C, the flash point is 127°C, the freezing point is -21°C, and the refractive index is 1.4678. The viscosity (20°C) is 101 MPa·sec.

When the temperature drops to 2.18K, the properties of liquid helium will change suddenly, the viscosity is very small, and it becomes a super fluid that can flow upwards along the wall of the container. The thermal conductivity is 800 times that of copper. It becomes a thermal conductor with excellent thermal conductivity. Its specific heat capacity, surface tension, and compressibility are all abnormal. This abnormal liquid is called liquid helium II, and the normal liquid helium is called liquid helium I.

Methacrylic acid is colorless crystal or transparent liquid with pungent odor. Soluble in hot water, soluble in most organic solvents such as ethanol and ether. Easily polymerized into water-soluble polymers. Combustible, there is a danger of burning in case of high heat and open flame, and it can produce toxic gas when heated.

This product is the standard configuration of SCR technology, the solution concentration is 32.5% 0.7%, which can effectively reduce exhaust pollution and ensure engine efficiency ;8-stage pretreatment + RO reverse osmosis technology + EDI electrodeionization water purification technology + high-precision filtration and purification to ensure the purity of the solution from the source, Delay SCR scaling, protect the urea pump and pipeline; select ultra-high-purity urea particles, made through multiple purification processes, long-term maintenance of the system and catalyst activity, and prol

it can also be used as high octane gasoline components, is an important raw material for organic chemicals. It can also be used to remove the bitumen of the body. The hospital pathology is primarily used for tissue, slice of pilot and dewaxing.

the crystal form of citric acid is exclusive due to distinctive crystallization conditions. it's miles barely weathered in dry air and hygroscopic in humid air. when heated, citric acid may be differentiated into diverse merchandise, that could react with acid, alkali, glycerin, and so on.

It uses oxygen with a purity of 93.5%-99.2% and combustible gas (such as acetylene) to produce a flame of extremely high temperature, thereby melting the metal. The metallurgical process cannot do without oxygen. In order to strengthen the production of nitric acid and sulfuric acid, oxygen is also required. Instead of using air, a mixture of oxygen and water vapor is blown into the coal gasifier to obtain coal gas with high calorific value.